about techmould techmould rubber mouldings about techmould rubber moulding services rubber mouldings injection mouldings FAQs FAQs FAQs news news about techmould
 
contact techmould
techmould rubber mouldings material specification
rubber moulders
 

 materials info...techmould

 

Typical Material Chemical Compatability

 
Natural Rubber
E.P.D.M.
Neoprene
Nitrile
HNBR
Flurucarbon
E.G. Viton
®
Silicone
Flurosilicone
Air or Oxygen
Fair
Very Good
Good
Good
Very Good

Excellent

Very Good
Very Good
Dilute Acids or Alkalis
Very Good
Very Good
Very Good
Good
Good
Very Good
Fair
Fair
Commercial Petrols
NR
NR
Fair
Good
Very Good
Very Good
NR
Fair
Fuel and Diesel Oils
NR
NR
Fair
Good
Very Good
Very Good
NR
Fair
Mineral Lubricating Oil
NR
NR
Very Good
Very Good
Very Good
Very Good
Fair
Very Good
Synthetic Lubricating Oil
NR
NR
NR
Fair
Very Good
Fair
Good
Fair
Mineral Hydraulic Oil
NR
NR
NR
Very Good
Good
Very Good
NR
Good
Water/Glycol
Fair
Very Good
Fair
Very Good
Very Good
Very Good
Good
Good
Water in Oil Emulsions
NR
NR
NR
Fair
Very Good
Very Good
NR
Good
Oil in Water Emulsions
NR
NR
NR
Fair
Very Good
Very Good
Fair
Good
Phosphate Ester
NR
Good
NR
NR
NR
Good
Good
Fair
Water above 80c
NR
Excellent
Fair
Fair
Very Good
Fair
Excellent
Very Good
N.R : NOT RECOMMENDED

The above information is provided as a guide only and suitability may be infuenced by other factors eg. Temp, Pressure etc. Specific recommendations will be given in response to full information

Typical Material Properties

 
Natural Rubber
E.P.D.M.
Neoprene
Nitrile
HNBR
Flurucarbon
E.G. Viton
®
Silicone
Flurosilicone
  Max Continuous degrees C
70
120
100
120
150
200
200
180
  Max Intermittent Temp degrees C
100
150
120
150
170
250
250
200
  Low Temperature Flexibility
-50
-45
-40
-20
-15
-15
-60
-60
  Hardness Range
30-95
40-95
30-95
40-95
50-95
50-98
20-80
40-80
  Tensile Strength
Excellent
Good
Good
Good
Very Good
Very Good
Poor
Poor
  Compression Set
Good
Good
Fair to Good
Good
Good
Good
Good
Good
  Tear & Abrasion Resistance
Excellent
Good
Good
Good
Very Good
Good
Poor
Poor
  Permeability to Gases
Poor
Fairly Low
Low
Low
Low
Very Low
Fairly Low
Fairly Low
  Flame Resistance
Poor
Poor
Self Extinguishing
Poor
Poor
Self Extinguishing
Excellent
Excellent
  Water Resistance below 80 degrees C
Very Good
Excellent
Good
Good
Good
Good
Good
Good
  Ozone & Weathering
Poor
Outstanding
Good
Fair
Good
Outstanding
Outstanding
Outstanding
  Cost Factor
1
1
2
2
6
15
4
40
 

   
The above information is provided as a guide only and suitability may be infuenced by other factors eg. Temp, Pressure etc. Specific recommendations will be given in response to full information.

Viton® is a registered trademark of DuPont Dow Elastomers

rubber moulders
rubber mouldings
diaphragms & valve seats
bellows suckers and tyres
rubber key pads
rubber electrical insulators
special rubber seals
rubber masking boots
rubber to metal bonding
cast polyurethane
ffkm Perfluoroelastomer
 
nqa
Sitemap
contact techmould